The N11752550W-ST1KBL from Nascom is a N1175 white switch with 1K resistor, blue leads and MN2550 Nd bare magnet. Nascom’s N1175 2550 Series, mini 3/8” recessed contact with cylinder neodymium magnet, protects all nonferrous (e.g. wood, aluminum and vinyl) doors and windows, in both residential and commercial settings. The N1175 2550 is the installer’s choice of contact configuration where drill depth is critical and excellent air and side-to-side gap are required to prevent false alarms caused by shifting or warping doors and windows.
Features
- Press Fit - No Glue Required
- Encapsulated Hermetically Sealed Contacts
- 12” 22AWG Wire Leads
- Polypropylene Housings
- Wide Gap - N35 NdFeB Rare Earth Magnet
- Listed To Ul634 Standard
Installation Instructions
- Mark location for the switch on the door frame and mark the location for the magnet on the top edge of the door
- Make sure switch and magnet hole locations are aligned
- Using a square, transfer the marks on to the top edge of the door and the opposing door frame
- Using a tape measure or graduations on the square, locate the center of the door edge and place an intersecting line with the first mark
- Drill a 3/8” hole at the location where the marks intersect
- Repeat the above step to locate the hole position for the switch in the door frame. Drill a 3/8” hole in the door frame
- Press the magnet into the hole you drilled in the door until flush with top edge of door
- Connect the switch leads to the alarm system. Caution! Hold wire leads, not the switch housing while cutting and stripping to prevent damage to switch
- Insert wire leads into hole followed by the switch and press the switch into the hole until the head is flush with the door frame
- Test switch for correct operation and make sure gap performance is acceptable
Additional Information
- Set: Switch/Magnet Special
- Color: White
- EndofLine (EOL) Resistors: SER
- Flange: Y
- Switch Size: D0.375' X L0.680'
- Magnet Size: D0.250' X L0.500'
- Termination: 22AWG UL 1061 RED
- Circuit Configuration: Closed Loop
- Lead Length (in.): 12
- Standard Ohm Resistor Values: 1K
Downloads
N11752550W-ST1KBL-Specsheet
The N11752550W-ST1KBL from Nascom is a N1175 white switch with 1K resistor, blue leads and MN2550 Nd bare magnet. Nascom’s N1175 2550 Series, mini 3/8” recessed contact with cylinder neodymium magnet, protects all nonferrous (e.g. wood, aluminum and vinyl) doors and windows, in both residential and commercial settings. The N1175 2550 is the installer’s choice of contact configuration where drill depth is critical and excellent air and side-to-side gap are required to prevent false alarms caused by shifting or warping doors and windows.
Features
- Press Fit - No Glue Required
- Encapsulated Hermetically Sealed Contacts
- 12” 22AWG Wire Leads
- Polypropylene Housings
- Wide Gap - N35 NdFeB Rare Earth Magnet
- Listed To Ul634 Standard
Installation Instructions
- Mark location for the switch on the door frame and mark the location for the magnet on the top edge of the door
- Make sure switch and magnet hole locations are aligned
- Using a square, transfer the marks on to the top edge of the door and the opposing door frame
- Using a tape measure or graduations on the square, locate the center of the door edge and place an intersecting line with the first mark
- Drill a 3/8” hole at the location where the marks intersect
- Repeat the above step to locate the hole position for the switch in the door frame. Drill a 3/8” hole in the door frame
- Press the magnet into the hole you drilled in the door until flush with top edge of door
- Connect the switch leads to the alarm system. Caution! Hold wire leads, not the switch housing while cutting and stripping to prevent damage to switch
- Insert wire leads into hole followed by the switch and press the switch into the hole until the head is flush with the door frame
- Test switch for correct operation and make sure gap performance is acceptable
Additional Information
- Set: Switch/Magnet Special
- Color: White
- EndofLine (EOL) Resistors: SER
- Flange: Y
- Switch Size: D0.375' X L0.680'
- Magnet Size: D0.250' X L0.500'
- Termination: 22AWG UL 1061 RED
- Circuit Configuration: Closed Loop
- Lead Length (in.): 12
- Standard Ohm Resistor Values: 1K
Downloads
N11752550W-ST1KBL-Specsheet
There are no reviews for this product.
No questions about this product.