Studio Technologies Model 372A Intercom Beltpack with Dante is prepared for professional supply, replacement, integration, or project procurement use. Key factual specifications include Network Technology: Type: Dante
Studio Technologies Model 372A Intercom Beltpack with Dante is prepared for professional supply, replacement, integration, or project procurement use. Key factual specifications include Network Technology: Type: Dante Audio-over-Ethernet AES67-2013 Support: Yes Dante Domain Manager (Ddm) Support: Yes Bit Depth: Up to 24 Sample Rate: 48 kHz Number of Transmitter (Output) Channels: 1 Number of Receiver (Input) Channels: 2 Dante Audio Flows: 4; 2 Transmitter, 2 Receiver; Network Interface: Type: 100BASE-TX, Twisted-Pair Ethernet, Power-over-Ethernet (PoE) Supported Data Rate: 100 Mb/S (10 Mb/S and 1000 Mb/S GigE Ethernet Not Supported); Compatibility: Headset A: Single- or Dual-Ear Broadcast-Style with Dynamic or Electret (Low-Voltage DC-Powered) Microphone: Pin-1 Mic Common; Pin-2 Mic; Pin-3 Phones Common; Pin-4 Phones Left; Pin-5 Phones Right Headset B: Ctia/Ahj Configuration (Typically Uses Electret Powered Mic): Tip Phones Left; Ring-1 Phones Right; Ring-2 Common; Sleeve Mic; Audio Channels: 1 x Talk, 2 x Listen; Microphone Input: Compatibility: Dynamic or Electret (Low-Voltage DC-Powered) Microphones Type: Unbalanced Electret Microphone Power: 3.3 Volts DC via 2.00 K Resistor, Selectable On/Off Impedance: 1 Kilohm, Nominal, Microphone Power Off; 690 Ohms, Nominal, Microphone Power On Gain: 24, 30, 36, 42, or 48 DB, Selectable, Ref. -60 dBu Input to Dante Output (-20 dBFS Nominal) Frequency Response: 40 Hz to 20 kHz, -3 dB Distortion (THD+N): <0.02% (at Minimum Gain) Dynamic Range: 91 dB of Dynamic Range.
Compatibility, quantity, lead time, shipping, and final project requirements should be confirmed before purchase.
Specifications
Box Dimensions (LxWxH)
8.9 x 7.2 x 4"
Call Handling
Implementation: Monitors Both Dante Receiver (Input) Channels for Presence of Call Signals Signaling Method: 20 kHz, ±800 Hz, within Audio Channels Call Receive Level: -27 dBFS Minimum
Compatibility
Headset A: Single- or Dual-Ear Broadcast-Style with Dynamic or Electret (Low-Voltage DC-Powered) Microphone: Pin-1 Mic Common; Pin-2 Mic; Pin-3 Phones Common; Pin-4 Phones Left; Pin-5 Phones Right Headset B: Ctia/Ahj Configuration (Typically Uses Electret Powered Mic): Tip Phones Left; Ring-1 Phones Right; Ring-2 Common; Sleeve Mic
Compressor
Application: Applies to Dante Transmitter (Output) Channel and Sidetone Audio Threshold: 2 DB Above Nominal Level (-19 dBFS) Slope: 2:1 Status Led: Compressor Active
Configuration
Requires Studio Technologies' STcontroller Software Application, Version 2.01.00 and Later
Connectors
Headset A: 5-Pin Female XLR Headset B: 4-Conductor (TRRS) 3.5 mm Jack, per Japanese Standard Jeita/Eiaj RC-5325A Ethernet: Neutrik NE8FBH etherCON RJ45 Receptacle USB: Type a Receptacle (Located Inside Model 372A's Enclosure and Used Only for Application Firmware Updates)
Dimensions
Width: 3.1" / 7.9 cm Height: 1.8" / 4.6 cm (With Belt Clip) Depth: 4.9" / 12.9 cm
Environmental
Operating Temperature: 32 to 122°F / 0 to 50°C Storage Temperature: -40 to 158°F / -40 to 70°C Humidity: 5 to 95%, Non-Condensing Altitude: Not Characterized
Headphone Output
Type: 2-Channel Compatibility: Intended for Connection to Stereo (Dual-Channel) or Monaural (Single-Channel) Headsets with Nominal Impedance of 50 Ohms or Greater Maximum Output Voltage: 2.8 Vrms, 1 kHz, 150-Ohm Load Frequency Response: 20 Hz to 10 kHz, -3 dB Distortion (THD+n): < 0.002% Dynamic Range: > 100 dB
Microphone Input
Compatibility: Dynamic or Electret (Low-Voltage DC-Powered) Microphones Type: Unbalanced Electret Microphone Power: 3.3 Volts DC via 2.00 K Resistor, Selectable On/Off Impedance: 1 Kilohm, Nominal, Microphone Power Off; 690 Ohms, Nominal, Microphone Power On Gain: 24, 30, 36, 42, or 48 DB, Selectable, Ref. -60 dBu Input to Dante Output (-20 dBFS Nominal) Frequency Response: 40 Hz to 20 kHz, -3 dB Distortion (THD+N): <0.02% (at Minimum Gain) Dynamic Range: 91 dB of Dynamic Range
Network Interface
Type: 100BASE-TX, Twisted-Pair Ethernet, Power-over-Ethernet (PoE) Supported Data Rate: 100 Mb/S (10 Mb/S and 1000 Mb/S GigE Ethernet Not Supported)
Package Weight
0.93 lb
Weight
0.5 lb / 0.23 kg
Audio Channels
1 x Talk, 2 x Listen
Network Technology
Type: Dante Audio-over-Ethernet AES67-2013 Support: Yes Dante Domain Manager (Ddm) Support: Yes Bit Depth: Up to 24 Sample Rate: 48 kHz Number of Transmitter (Output) Channels: 1 Number of Receiver (Input) Channels: 2 Dante Audio Flows: 4; 2 Transmitter, 2 Receiver
