Bitrate is the amount of encoded data a camera stream produces per second. It affects network traffic and recording storage, but a higher number does not automatically deliver better evidence. Useful footage depends on the entire imaging chain: scene, lens, lighting, exposure, compression, and recording settings.

Understand the units first
Camera menus commonly show kilobits per second (kbps) or megabits per second (Mbps). Storage capacity is usually expressed in bytes. Eight bits make one byte, so a 4 Mbps stream represents approximately 0.5 megabytes per second before considering additional data and overhead.
Using decimal units, that stream produces about 1.8 GB per hour or 43.2 GB per day if it records continuously at that average rate. These are arithmetic examples, not recommended settings for every camera.
| One stream's average rate | Video payload per 24 hours | Video payload per 14 days |
|---|---|---|
| 2 Mbps | 21.6 GB | 302.4 GB |
| 4 Mbps | 43.2 GB | 604.8 GB |
| 8 Mbps | 86.4 GB | 1,209.6 GB |
Calculated examples for continuous recording, using decimal units and excluding overhead. These figures describe bitrate, not a guaranteed result for a particular codec.
Why two similar cameras can need different bitrates
Resolution and frame rate matter, but so do the scene and encoder settings. Busy backgrounds, moving foliage, rain, traffic, and image noise can make video more difficult to compress. A quiet daytime test may therefore underestimate what the system will produce at night or during a busy shift.
Compression settings also involve tradeoffs. Too little data can obscure important detail through blockiness or other artifacts. Adding more data beyond the useful quality level can consume bandwidth and storage without solving problems caused by poor focus, insufficient illumination, or motion blur.
CBR versus VBR
| Mode | General behavior | Planning consideration |
|---|---|---|
| CBR: constant bitrate | Attempts to maintain a configured data-rate target. | Can make traffic more predictable, but the encoder may sacrifice detail during complex scenes. Short-term behavior and limits vary by product. |
| VBR: variable bitrate | Allows the amount of data to change with scene complexity and the selected quality settings. | Plan for peaks as well as average usage. A quiet-scene average is not a capacity guarantee. |
| Other vendor controls | May offer maximum-rate limits, average-rate targets, or storage-oriented modes. | Read how the specific implementation prioritizes quality, frame rate, and rate limits. |
Neither mode is universally best. A constrained link may call for carefully controlled traffic; a quality-focused recording system may benefit from variable rates with sufficient headroom. Test the result rather than assuming the same menu label behaves identically on different camera models.
Do not confuse the local network with the internet connection
Cameras recording to an NVR on the same local network do not necessarily send all of that footage through the internet connection. Size the camera links, switch uplinks, recorder interfaces, and remote-viewing path separately.
For example, eight streams averaging 4 Mbps each create 32 Mbps of video payload on a path that carries all eight. Additional streams, playback, exports, other network traffic, and protocol overhead can add to that load. Camera peaks may also exceed the average.
If a remote viewer requests lower-resolution substreams, its bandwidth needs can differ from the main recording streams. Cloud recording has its own upload requirements. Identify which streams cross each link before choosing network equipment or estimating internet usage.
Calculate storage from average recording bitrate
A useful starting estimate for continuous recording is:
Storage in decimal TB = total average recording bitrate in Mbps × 0.0108 × retention days.
Suppose eight cameras each average 4 Mbps and record continuously for 14 days. The total average is 32 Mbps, so the estimated video payload is 32 × 0.0108 × 14 = 4.8384 TB.
This excludes extra capacity for recording overhead, audio or metadata not included in the stated rate, filesystem use, redundancy, and operating headroom. It also assumes that the average remains representative. Do not select an array by rounding this figure down.
Motion-based recording changes the amount of recorded time. Estimate it from observed activity and the configured pre-event and post-event periods, rather than assuming that motion recording always saves a fixed percentage. Axis likewise notes in its storage guidance that bitrate needs vary by installation.
Choose codecs for the whole workflow
H.264 and H.265 are common options, but the right choice depends on what the cameras, recorders, clients, and export tools support. H.265 is not restricted to 4K cameras, and its storage savings are not a universal fixed percentage. Compare the same scene at a quality level that preserves the detail you need.
Check live viewing, playback, and exported files before applying a codec change across the site. A setting that records successfully but cannot be conveniently reviewed on the intended client can create an operational problem.
A practical tuning sequence
- Define the evidence task. Identify the area and moving detail that must remain useful.
- Set the view and exposure. Correct focus, lighting, and motion blur before using bitrate to chase image quality.
- Select resolution and frame rate. Match them to the task and equipment capabilities.
- Choose a compatible codec and rate-control mode. Start with the manufacturer's supported recommendations.
- Record representative scenes. Include busy periods, quiet periods, and night operation.
- Review the recording itself. Inspect moving subjects and export a sample; a good live preview does not prove the archive is correct.
- Measure average and peak traffic. Recalculate network and storage needs, then leave appropriate headroom.
Keep a record of the final settings and measured results. Recheck them when lighting, scene activity, camera count, or retention needs change. Explore CCTV systems in the Safsale catalog and use the practical surveillance guide to connect bitrate planning with the rest of the installation.
Related products from Safsale
Continue from Academy guidance to live equipment and components available on Safsale.
Reolink Argus-2e Indoor/Outdoor Wire Free Smart Security Camera 1080pView product
Hanwha Vision SND-6084 2MP Full HD Day/Night IP Dome Camera, 3-8.5mmView product 